The 2015 has a single magnet for the sleep sensor while the 2016-2017 has two. Unfortunately, 2013/13" Display has different Camera connector.įor testing 13 and 15 inch screens of the same generation are compatibleįD46, FF0H, FF0J, FF0K, FF14, FFJ4, FGFY, FGG0, FY1C, FY1F, FY1G, FY1HįW3D, FW3F, FW3G, FW3H, G1FQ, G1FR, G1FT, G1FVįD4N, FF0N, FF0P, FF0Q, FF20, FFG2, FFJ5, FFJ6, FY94, FY95, FY96, FY97įWKN, FWKP, FWKQ, FWKR, GCQ0, GCQ1, GCQ2, GCQ3Ģ015-2017 are all compatible, with the exception of the sleep sensor. Two dots of hot glue behind the plug will work perfectly to secure the plug in place, and hot glue can be removed cleanly from whatever surface it's bonded to with isopropyl alcohol.Īll Retina screen cable with hinge are compatible.Ī1425 2012L 13" Retina could be tested with 13" or 15" 2013E Display. You will likely need to remove the little clip that secures the plug into the socket as part of this mod.BE SURE TO CHECK FOR SHORTS AFTER YOU'VE INSERTED THE MODIFIED PLUG INTO THE SOCKET! You don't want your backlight voltage shunted straight to ground!.To use a 2010-2011 LCD with a 2012 logic board, you'll need to either replace the LVDS connector on the logic board with one compatible with the 2010-2011 era screen, or modify the display connector by trimming some plastic off of the edges.īelow are examples of a 2011 15in screen assembly being modified to work with a 2012 logic board:Īnd here you can see that the plug fits into the 2012 socket. If you expose the internal acoustic chamber on the subwoofer assembly, it can be resealed easily with hot glue.ġ5 and 17 inch screens can not be swapped for testing purposes. Also, the 2010 screen assemblies only have two wifi antenna lugs built in and the camera cable is shorter than what is ideal for connecting to a 2011 or 2012 logic board so you may have to get creative with your routing or trim down the subwoofer assembly plastic to make room for the cable to cut a corner. 2010-2012 display assemblies are fully compatible, but the LVDS connector is slightly different for the 2012 units and so it would need to be modified or replaced if you're using a 2010 or 2011 screen assembly with a 2012 logic board, or vice versa.
Mid-2009 - 2012 LCDs are compatible but the wifi and camera connector is different for 2009 than for 2010-2012, so 2009 assemblies can only be used interchangeably for display purposes exclusively.They have a different LCD that is not compatible with the later models. Late 2008 - Early 2009 screen assemblies are fully compatible, but only with each other.(The 2012 LVDS can plug in fine to a 2011 - But not the other way around) 2011-2012 screen assemblies are fully compatible, but the LVDS connector is slightly different and needs to be modified or replaced.2009-2012 LCDs are compatible but the wifi and camera connector is different for 2009-2010 than for 2011-2012, so they can only be used interchangeably for display purposes exclusively.2009-2010 screen assemblies are fully compatible.Some work or work partially regardless.Ģ010-2017 Airs have compatible LCDs 11 and 13 inch can be swapped for testing purposes. Some model numbers are officially interchangeable, some are not.
Macbook pro mid 2010 15 monitor code#
Look for this code under the 2D barcode on LVDS or right beside it.Īn EEE code is a model number for the screen. To determine the original model of a screen use the EEE code.
0 kommentar(er)
